Instructions for use

Preparation

• Always use appropriate gloves.
• Into a non-metallic bowl, pour the required quantity of Tocco Magico Freelux color cream color.
• Always use a clean, flat brush to emulsify the product. Stir slowly, and then add the Tocco Magico Oxy Developer of your choice (10/20/30/40 vol., mixing 1 part color cream with 1.5 parts of Tocco Magico Oxy).
• Mix until you achieve a uniform emulsion.
• Apply a barrier cream around the entire hairline, including ears and nape, before color application.

Retouch application

• Divide hair into four cross-sections.
• Apply color cream to the re-growth area of the first back section and then the second back section, always starting from the center of the head. Then apply to the re-growth area of the two remaining front sections (during application, divide hair into 1/2 inch sections).
• Then uniformly apply on mid-shaft and ends.
• Processing time: approximately 30 minutes.

Application

Step 1

• Divide the hair at the center of the head from ear to ear.
• Apply color emulsion to mid-shaft, starting from 1/2 to 1 inch (2.54 cm) from the scalp. Work from the back part to the front part and divide hair into 1/2 inch sections during application.
• Processing time (mid-shaft and ends): approximately 15 minutes.

Step 2

• Apply color emulsion to re-growth from 1/2 to 1 inch (2.54 cm) from the scalp, starting from the nape.
• Processing time: approximately 15 minutes.
• Total processing time: approximately 30 minutes.

Rinsing and cleansing

• After color processing is complete, simply add warm water to the color and emulsify. Rinse out the color thoroughly.
• After rinsing, follow with thorough cleansing. Use a specific post-chemical treatment. Massage uniformly onto scalp and hair. Rinse thoroughly.
• Remove excess water from hair and apply a post-chemical treatment mask to mid-shaft and ends using a wide-tooth comb.
• Leave it on for several minutes, then rinse thoroughly.

Ingredients:

Aqua (Water), Cetearyl alcohol, Ethanolamine, Cocamide MEA. Stearic acid, Decyl oleate, C12-13 Pareth-5, Polyacrylammide, Oryza saliva (Rice) bran oil. Olus oil, Tri-C12-13 alkyl citrate, Steareth-20, Glyceryl stearate, Cetyl alcohol. Toluene-2,5-diamine sulfate, PEG-75 Stearate, Camellia japonica seed oil. 4-Chlororesorcinol, Ceteth-20, Sodium metabisulfite, Cocamidopropyl betaine. Dipropylene glycol, Boswellia serrata gum, Ascorbic acid. Sodium Hyaluronate. 2-Chloro-p-phenylenediamine sulfate, Arginine. Parfum (Fragrance), 2-Amino-3-hydroxypyridine, N,N-bis(2-hydroxyethyl)-p-phenylenediamine sulfate, C12-13 Alkyl lactate, Sodium chloride, Ceteth-2, Aloe barbadensis leaf juice powder, Aniba rosaeodora (Rosewood) wood oil, PVP, PVA, Glycerin, EDTA. Peg-8, Sodium benzoate, Peg-8/SMDI copolymer, Palmitoyl myristyl serinate. Sodium polyacrylate, 2.4-Diaminophenoxyethanol HCI.

Patch Test Instructions for Freelux Color:

Freelux Color is designed to be skin-friendly. However, individual sensitivities to hair color vary, and thus a patch test is legally required as a precautionary measure before application.

Follow these simple steps for a patch test:

1. Cleanse a Test Area: Wash and dry a small area (about the size of a quarter) on the inner fold of your elbow.
2. Apply the Test Mixture: Using a cotton-tipped applicator, apply a small amount of the test mixture to the cleansed area and allow it to dry.
3. Leave it Undisturbed: Do not touch or wash the test area for 24 hours.
4. Observe for Reactions: If at any time during this test, you notice signs of irritation, redness, burning, itching, swelling, or any abnormal reaction, please do not use Freelux Color.

⚠ Important: Freelux Color must not be applied to the hair if the patron's scalp shows any evidence of abrasion, eruption, or any other diseased condition.